Second Independent POD Replication
The following post was made entirely unsolicited to an Egroup recently. I have been unable to procure a photo, but the replication claim remains fully valid. Since no photo has been offered, I have decided not to give a separate web page to this device. I must say this is one area of misunderstanding. Some people seem to think I have the power to force people to buy webcams and post their full names, address, and telephone numbers on the internet. In reality, most people replicating the...
John Jankowskis Transductor Device Important General Construction Notes
The coils must be wound directionally as indicated and connected in series as shown. Counter clockwise wind is determined by facing the nail core head or PM directly and proceeding The use of the thin double sided tape as insulation is convenient and beneficial. Best results were obtained at 9v - the first negative energy harmonic value Stator wind depth can be set by placing a paper clip in front of a magnet pole face, and moving it closer until such time as frictional forces are overcome, and...
All magnetic fields have poles a possible mechanism for negentropy
My friend John Jankowski has very kindly supplied a diagram of the possible true nature of magnets, putting solid pictorial form to my theories. Even if this graphic turns out to be wrong, the temporarily enlarged time reversed secondary poles, are an excellent way to visualize the field depletion process manifested in the Adams motor. One can model the negative impulse mathematically, but that is different from the actual physics of how the effect is in reality manifested. Areas of least...
Third Independent POD Replication
futuresky123 posted this to the Adams motor Egroup Greetings, I've recently been experimenting with Parallel Path but decided to set it aside for now and replicate POD. I have already built a working Adams motor that runs cold, but have yet to measure cop. So I took one of the stators from my Adams motor and wired it per POD specifications, and low and behold the current draw halves. The POD I built uses ring magnets stacked from speakers that are rather large, 3 8 bolt for core. I built the...
V Lh
Permanent magnet with locationofhidden i time negative vortex i field replenishment 1 ' 1 ' poles illustrated Areas of greatest classical magnetic attraction The secret of over-unity is separating out these two components of magnetic fields The cold field is attracted to conductive substances such as iron steel The hot field is attracted to and feeds oif permanent magnets This is the basic principal the POD unit works upon
Response to detailed questions from successful POD constructor
Q The unit is not cold running. It actually runs quite warmly. I am not yet using the circuit that was provided on the web page. I am using a 555 timer circuit with which I use variable resistors to change the frequency and duty cycle, with a MOSFET switch. I am trying to understand the functioning of this device by using this setup and monitoring the effects with my oscilloscope. When constructed per the site, the arrangement runs room temp to cool. This varies between components with the only...
Sweet VTA
This device appears to have manifested the same negative energy as the Adams motor. 'Negative energy is fully capable of lighting incandescent lights, running motors, and performing all of the functions of positive energy tested to date. When run in parallel with positive energy however, cancellation annihilation of opposing power types occurs. This has been fully tested in the laboratory.' 'The coils are very small diameter copper wire but are capable of producing in excess of 5 kilowatts of...
Back Emf a Common Source of Confusion
Back emf is a Lenz effect reversed polarity current surge that happens whenever current is suddenly stopped - as happens all the time in a pulse motor. Many people confuse back emf with the negative energy manifested in the Adams motor. Transducted negative time reversed energy flows BACKWARDS to its source - hence enormous amounts of what people assume is 'back emf' can be extracted from Adams motors, with 97 of input already seen with magnetite cores. You treat it as if it is back emf, it...
Clarification of above
In permanent magnet switched reluctance design, it is important to understand the windings are fundamentally demagnetizing windings, and NOT as many people intuitively assume - magnetizing windings. Important difference. This is not to say the windings can not with enough voltage be used as magnetizing windings, but this is not really the proper mental image to use to visualize how the motor functions. Try it this way - the units I am about to used are not intended to correlate to real values,...
The Tesla Connection a reminder
Secrets of Cold War Technology Project HAARP and Beyond, by Gerry Vassilatos. This book is well worth the money, and I don't say that about many. Much wonderful original research on Tesla. Genuinely very helpful. Obtaining a copy of this book appears to have transformed Mr Adams' research in the mid to late 1990s, with his latest models gating the 'back emf into high voltage capacitors 250v , which then deliver the pure voltage wattless zero amp, state of energy Tesla documented over a century...
Solid State OverUnity COP Transductor
Costing a Solid State Transductor - List of Parts You Need for Construction Basic ceramic ferrite parts are fine Basic ceramic ferrite parts are fine, can use3 4 thin For output conversion to DC, 4 diodes, essentially Solid state o u for 40 with Radio Shack parts
Brief History
Invented in the period 1967-1969 by Mr Robert Adams of New Zealand, for a variety of reasons the technology did not win immediate acceptance, not least of which was that the New Zealand government and the Lucas corporation, for various reasons, allegedly directly suppressed it, followed by a typically botched and incompetent CIA assassination attempt. That this direct suppression could happen during a period of global economic crisis triggered by the 1970s oil shock, is simply astonishing, and...
Magnets
The negative impulse delivered by the pms rapidly decays to zero as soon as the timing switch is closed. Hence the larger your magnets, the longer the pulse duration required, the harder it becomes to obtain 'cold current.' However, too small a magnet, and no 'yaw to register' is manifested - ESSENTIAL for the generation of the negative impulse in the first place. Push only motors can only ever be hot current devices. My basic conclusion is that magnets of diameter 15-20mm are the sweet spot...
The First Attempt At a Solid State Lenz Gate
Best delivered performance was a dissapointing 84 Without the benefit of the 'yaw' into register in the Adams motor We realized we needed something extra to make it work And trigger the true time reversed 'cold current1 we wanted The project reasoning, methodology, and underlying field depletion theory, was directly copied from my successful over-unity CD motor project. We wanted to generate negative energy in a solid state setup, and initially cold running was made the primary device...
COP Figures Mechanical not electrical overunity
If properly wired to send the emf back to an appropriate rechargeable source battery, mechanical COP figures of 3-6 are possible with the CD motor unit. That depends upon such factors as quality of construction, stator winds, and measurement methodology. Given the problematic nature of mechanical efficiency calculations, many prefer to use the crude 'back emf to supply' metric, to measure the performance of their units. As a rough guide, allowing for the halved current draw effect and the...
In Search of Nikola Tesla The Quest for Cold Electricity Tesla Radiant Energy
Nikola Tesla. To understand negative energy two simple new scientific terms are required. Hot Current This is the normal form of electrical charge. Since 101 textbooks abound, no further discussion is required. Cold current This is simply the time reversed counterpart of normal hot current. Discussion of cold current A device that time reverses an electromagnetic wave is called 'phase conjugate mirror,' in the standard scientific literature. The concept is not in any way new or outlandish, but...
Important Recent experimental validation of secondary vortex pole theory
Solid state experiments have now shown that air cored stators are not capable of delivering cold current. This conclusively proves it is not the flux field of the magnet that becomes time reversed negative - only a relatively small part on on the magnet pole faces, that does not ordinarily extend far from the physical limits of the magnet, even when field depletion has occurred. An iron core attracts this secondary pole, and conducts it along its length over the generator turns, enabling phase...
Close up of Adams Stator Rotor Interaction
Stator windings are potentialised pre charged by field of magnet When circuit closes charge manifested in windings is above supply Precise geometrical use of'Lenz gate' enables load less energy gain Magnet's flux field becomes time reversed negentropic to restore itself Circuitty within flux field also becomes time reversed Photons directly convert disordered heat energy from the vacuum to potential If field depletion is sufficient, electrons flow backwards, giving polarity reversal 1 2 width...
Device Schematics
This is John's very own schematic of his device, which gives more detailed and precise technical information about the device, than the previous simple background and introduction to principal images offered. Copyright John Jimkowski amp Tim Harwood 2002 www.geocities, com lheadamsmotor Copyright John Jimkowski amp Tim Harwood 2002 www.geocities, com lheadamsmotor 15 16 O.D, X 5, X 1 15 1.6- LQN RING MAGNET STA John's second image gives precise circuitry details. Again, nothing especially...
Fully Independent Adams Motor Replication
This motor is a successful over-unity cold current design. The constructor wishes to remain anonymous. He also warned me, these pictures show an early version, and significant modifications were subsequently undertaken. Exact mechanical efficiency numbers are not available, but they are clearly well over 100 . The constructor so far measures his performance by the amount of back-emf he can pull off relative to input - 97 . Which is absolutely astonishing Secondary windings could most easily be...
Circuits
TimHarwood's CD Adams Motor c 2001 TimHarwood's CD Adams Motor c 2001 Bill offers the following advice based upon his research and analysis with Dragone cores The PNP needs a diode to gate the current back to the battery. Mosfets have this diode built in. Because you are using a PNP, the negative energy has nowhere to go but remain in the coil and ring. If the negative energy were high enough, it could breakdown the transistor. Keep in mind that negative energy appears as a high voltage when...
Another Cold Running Adams Motor Using A Hard Drive Platter to Make an NIB Motor
This fascinating motor was based upon a rotor scavenged from an old computer hard drive. Hence as one would expect, it is almost entirely frictionless, and also very well calibrated. Between the dual hard drive platters reside 4 1 2 12.7mm square faced NIB magnets, fixed in place with high strength epoxy glue, at 90 degrees apart. The diameter of the hard drive platters disks is 130mm. The stator cores are made from permalloy these were found to produce better results than relay cores . The...
The Stator An Electromagnetic Field Splitter
Firstly the central core. A piece of material that is in an ideal world magnetically non retentive, highly permeable, with a very low magnetic orientation and response time, and an inductance rating of 1.5 Teslas or above Obviously, the rotor will be most strongly attracted to this substance. Secondly, the stator is wound with many hundred of turns of wire, the current induced in this wire by the magnet will be of a polarity that repels the magnet, as per Lenz. The 1.5 Tesla inductance rating...
Brians CD Motor Replication
I was most gratified to see Brian finally get a result with this motor. He really did put a lot of genuine hard work into this device, and he most definitely deserved a positive result. I think the fact he opted for 1 magnets with a longer pulse duration complicated this motor, but the problems that created have recently been solved with 555 circuitry to adjust the pulse width down. Instead of running hot and slow, it now runs fast and cold - as it should. Pulse width is key, and even if he is...
Setting Stator Wind Depth The Paper Cp Test
No need to over complicate this process Take one permanent magnet, and one paperclip Place on smooth surface, and push paper clip towards pm Note distance at which paper clip flies into face of magnet Repeat to verify test result Your stator winding depth is now set Mr Adams refers to using batteries to 'tune,' his motor at low voltage 9-12v , before taking his motor up to the 120v or 240v range, which is where the real action happens. No exact guidance is given on how to do this however. Now I...
Feedback notes
Q What sort of cct is used to pulse the coil with 60Hz I initially used a crude mechanical commutator made from a small dc motor, but a solid state arrangement could should be tried. Or, if a 60hz line supply setup were used, one could utilize the non filtered pulsing dc from that with no further frequency manipulation needed. 555 circuitry can also be employed. Motor variations are so simple I do not understand how anyone could have trouble fixing a basic 60hz supply. Pat in the AM Egroup I...
Example application Monster Truck Madness
Radio Control Full Function Nissan Frontier with 9.6V Battery and Charger 27 MHz A POD unit could be fitted onto the back of this truck, significantly extending the rather short battery life of 30-45 minutes. The POD enhanced battery life would really be dependant upon the quality of your engineering, so much as any inherent limitation in the POD performance curve. This is a simple example of how much good clean fun is to be had with POD technology - I am sure you can think up many others....
Solid State Transductor Technology
The POD technology is astonishingly cheap, simple, flexible, robust, and effective. Too many possible configurations and applications exist for this web site to even attempt to cover a fraction of them. This being the case, the POD 2 layouts on this page, present only some of the most obvious further optimizations that can be undertaken. I highlight the following features for particular attention 1. The circuitry switch closed only during the pulse 2. Increasing the capacitor voltage to 250v 3....